LG AC CH93 Error Code
Communication problem between the indoor and outdoor units, typically during the test-run phase. Here's what it means, what you can safely check, and when to call a technician.
LG AC CH93 Error: Communication problem between the indoor and outdoor units, typically during the test-run phase
When your LG ac shows a CH93 error, it is indicating: Communication problem between the indoor and outdoor units, typically during the test-run phase. This is a specific fault code the appliance's control board uses to flag a problem it has detected — it won't clear permanently by switching the power off and on, because the underlying condition that caused it still exists.
What To Check Before Calling a Technician
For units from 2021 onward, also check that the outdoor unit itself is receiving power — these models have a separate power cord for the outdoor unit specifically.
Check the power cord and cable connections to the outdoor unit are secure. Power cycle (unplug 5 minutes); if it persists, request service. If the CH93 error persists after the checks above, a technician will be able to diagnose and fix it with the right tools — attempting to open the unit's panels or handle electrical components without training is not safe.
Frequently Asked Questions
What does the CH93 error mean?
Communication problem between the indoor and outdoor units, typically during the test-run phase.
What should I check first?
For units from 2021 onward, also check that the outdoor unit itself is receiving power — these models have a separate power cord for the outdoor unit specifically.
Can I fix this myself, or do I need a technician?
Check the power cord and cable connections to the outdoor unit are secure. Power cycle (unplug 5 minutes); if it persists, request service.
Other LG AC Error Codes
- CH04 — Drainage issue — condensate water is not draining properly
- CH05 — Communication error between the indoor and outdoor units (also shown as E0 or CH53)
- CH07 — Conflicting operation modes on a multi-unit (2-in-1 or ceiling-type) system
- CH10 — Indoor unit fan problem (the equivalent outdoor-unit fan fault shows as CH67 or EF)
- CH38 — Low refrigerant (gas) level — a protective warning, also shown as F4
- CH54 — Reverse phase detected in the electrical supply
- CH61 — Overheating protection — outdoor unit overheating in cooling mode, or indoor unit overheating in heating mode (also shown as P4, P6, P7, P8, or CH34 depending on model)
- CH66 — Communication or piping connection issue between the indoor and outdoor units
- CH90 — Protective error typically shown during the test-run phase right after installation (also shown as CH91 or F4 on some models)
Understanding and Troubleshooting the LG AC CH93 Error Repair
The LG AC CH93 error code is a specific diagnostic signal indicating a communication failure or an electrical anomaly within the outdoor unit's inverter circuit. When this code appears on your display, it typically means the main control board is unable to receive consistent data from the outdoor compressor drive, often triggered by voltage fluctuations or component degradation. As an independent repair service, we specialize in diagnosing these technical faults across Tamil Nadu to restore your cooling system efficiently.
Common Causes of the CH93 Error
- Voltage Instability: Sudden power surges or drops can disrupt the communication signal between the indoor and outdoor units.
- Loose Wiring Connections: Vibration over time may cause terminal connections to loosen, leading to intermittent signal loss.
- Inverter PCB Failure: The outdoor control board may have developed internal faults, preventing it from processing commands correctly.
- Compressor Overload: High thermal stress on the compressor can trigger the protection circuit, resulting in the CH93 error.
- Damaged Inter-unit Cable: Physical damage or oxidation on the communication wire between the indoor and outdoor units can block data transmission.
Frequently Asked Questions
Can I reset the LG AC CH93 error by unplugging the unit?
While a power cycle may temporarily clear the error, it does not resolve the underlying electrical fault. If the error persists after a 10-minute reset, professional inspection of the inverter PCB and wiring is required.
Is the CH93 error dangerous for my AC?
Continued operation with this error can lead to further damage to the compressor or the inverter board. It is recommended to turn off the unit until a technician can verify the electrical integrity of the system.
If you are facing persistent error codes, our experienced technicians provide reliable, same-day service to get your cooling back on track. Contact us at 99520 78200 for professional assistance wherever you are located.
Get a Technician Today
Opens WhatsApp with your details pre-filled — we'll confirm your visit window directly. Trouble opening WhatsApp? Call us instead.