LG AC CH66 Error Code
Communication or piping connection issue between the indoor and outdoor units. Here's what it means, what you can safely check, and when to call a technician.
LG AC CH66 Error: Communication or piping connection issue between the indoor and outdoor units
When your LG ac shows a CH66 error, it is indicating: Communication or piping connection issue between the indoor and outdoor units. This is a specific fault code the appliance's control board uses to flag a problem it has detected — it won't clear permanently by switching the power off and on, because the underlying condition that caused it still exists.
What To Check Before Calling a Technician
Check whether this appeared right after a new installation or relocation — this points to the connection itself, not a later fault.
If it appeared right after installation, contact the installation technician directly. If it happens during normal use, power cycle (unplug 5 minutes); if it persists, the unit needs a technician. If the CH66 error persists after the checks above, a technician will be able to diagnose and fix it with the right tools — attempting to open the unit's panels or handle electrical components without training is not safe.
Frequently Asked Questions
What does the CH66 error mean?
Communication or piping connection issue between the indoor and outdoor units.
What should I check first?
Check whether this appeared right after a new installation or relocation — this points to the connection itself, not a later fault.
Can I fix this myself, or do I need a technician?
If it appeared right after installation, contact the installation technician directly. If it happens during normal use, power cycle (unplug 5 minutes); if it persists, the unit needs a technician.
Other LG AC Error Codes
- CH04 — Drainage issue — condensate water is not draining properly
- CH05 — Communication error between the indoor and outdoor units (also shown as E0 or CH53)
- CH07 — Conflicting operation modes on a multi-unit (2-in-1 or ceiling-type) system
- CH10 — Indoor unit fan problem (the equivalent outdoor-unit fan fault shows as CH67 or EF)
- CH38 — Low refrigerant (gas) level — a protective warning, also shown as F4
- CH54 — Reverse phase detected in the electrical supply
- CH61 — Overheating protection — outdoor unit overheating in cooling mode, or indoor unit overheating in heating mode (also shown as P4, P6, P7, P8, or CH34 depending on model)
- CH90 — Protective error typically shown during the test-run phase right after installation (also shown as CH91 or F4 on some models)
- CH93 — Communication problem between the indoor and outdoor units, typically during the test-run phase
Understanding and Troubleshooting LG AC CH66 Error Repair
The LG AC CH66 error code is a specific diagnostic signal indicating a communication or power supply issue within your air conditioning system. Typically, this code points toward an inconsistency in the voltage levels between the outdoor unit and the indoor controller, or a failure in the inverter PCB's ability to regulate power effectively. When this error appears, the system usually shuts down to prevent further damage to the sensitive electronic components.
Common Causes for CH66 Error
- Inverter PCB Failure: The main power module responsible for converting AC to DC power may have developed a fault, preventing the compressor from starting.
- Voltage Fluctuation: Unstable power supply or frequent surges in your area can cause the system to trigger a safety lockout to protect the internal circuitry.
- Loose Wiring Connections: Vibrations over time or improper installation can cause communication cables between the indoor and outdoor units to loosen or corrode.
- Capacitor Degradation: A failing capacitor in the outdoor unit may struggle to provide the necessary starting torque, leading to a power mismatch that registers as an error.
Can I reset the LG AC CH66 error by turning it off and on?
While a power reset might temporarily clear the code, it does not fix the underlying electrical fault. If the error persists after a 10-minute power cycle, it indicates a hardware issue that requires professional inspection.
Is the CH66 error dangerous for my AC?
The error is a safety mechanism designed to prevent catastrophic failure. Continuing to force the unit to run while this code is displayed can lead to permanent damage to the compressor or the main control board.
If you are experiencing this issue, our independent technicians are ready to assist you across Tamil Nadu. We provide reliable, same-day service to get your cooling system back in operation. For professional assistance, please contact us at 99520 78200.
Get a Technician Today
Opens WhatsApp with your details pre-filled — we'll confirm your visit window directly. Trouble opening WhatsApp? Call us instead.