Serving Tamil Nadu & Surrounding Areas Mon–Sun: 8AM–9PM Same-Day Response
CALL NOW 99520 78200
Washing Machine Troubleshooting Guide

Washing Machine Keeps Filling with Water on Spin Cycle

If your washing machine continues to take in water while it is supposed to be spinning, it can lead to overflowing and poor drying performance. This issue usually points to a malfunction in the components that control water flow and level sensing. Follow this guide to identify and troubleshoot the most common causes.

Checking the Water Inlet Valve and Pressure Switch

  1. Inspect the water inlet valve for debris or a faulty solenoid that may be stuck in the open position, allowing water to pass even when the machine is off.
  2. Check the pressure switch (water level sensor) by ensuring the thin plastic tube connected to it is not kinked, blocked, or detached, as this prevents the machine from knowing the tub is empty.
  3. Test the pressure switch for continuity using a multimeter to confirm if it is correctly signaling the control board to stop the water flow.

Safe Steps to Try Before Calling a Technician

  1. Turn off the water supply taps connected to the washing machine to prevent flooding while you inspect the unit.
  2. Unplug the power cord from the wall outlet to eliminate any risk of electrical shock during your inspection.
  3. Clean the inlet filters located at the back of the machine where the hoses connect, as sediment buildup can sometimes prevent the valve from closing tightly.

Always disconnect the power supply and water source before opening the machine casing to avoid the risk of electric shock or water damage.

How It Works

  1. 1

    Call or WhatsApp

    Tell us the appliance, issue, and your area.

  2. 2

    Technician Visits

    We inspect the unit and give an upfront quote.

  3. 3

    Repair & Pay

    Approve the quote, repair completed same-day, pay after.

Why Choose Us

What You Get With Every Repair

30-Day Repair Warranty

If the same issue recurs within 30 days of the repair, we'll fix it again at no extra visit charge.

Frequently Asked Questions

Why does my washing machine fill with water even when it is turned off?

This is typically caused by a faulty water inlet valve that has failed in the open position, allowing water pressure from your home supply to enter the drum constantly.

Can a clogged pressure switch tube cause overfilling?

Yes, if the pressure switch tube is blocked or disconnected, the machine cannot accurately detect the water level, which may cause it to continue filling or fail to start the spin cycle.

Is it safe to use the machine if it fills during the spin cycle?

No, you should stop using the machine immediately as it can lead to water overflowing onto your floor, potential damage to the motor, and electrical hazards.

Do I need to replace the entire valve or just clean it?

If the valve is physically damaged or the solenoid is burnt out, it must be replaced. Cleaning is only effective if the issue is caused by minor mineral deposits or debris.

Why Your Washing Machine Keeps Filling With Water on Spin Cycle

If you notice that your washing machine keeps filling with water on spin cycle, it is usually a sign that the appliance is struggling to transition between its wash and drain phases. This issue often points to a malfunction in the components responsible for regulating water flow and sensing water levels.

Troubleshooting Key Components

The two most common culprits are the water inlet valve and the pressure switch:

  • Water Inlet Valve: This valve controls the flow of water into the drum. If the valve is faulty or has debris stuck in the solenoid, it may fail to shut off completely, allowing water to trickle in even when the machine should be spinning.
  • Pressure Switch (Water Level Sensor): This component tells the machine how much water is in the drum. If the pressure switch or its connected air tube is clogged, damaged, or disconnected, the control board may incorrectly "think" the drum is empty or needs more water, triggering the inlet valve to open during the spin cycle.

Can I fix a faulty water inlet valve myself?

While you can inspect the valve for visible debris, replacing it requires technical knowledge of your machine's internal wiring and plumbing. If the valve is defective, it must be replaced to prevent flooding or further electrical issues.

Is it dangerous to run the machine if it keeps filling?

Yes, running a machine that fills unexpectedly can lead to water overflow, potential floor damage, and strain on the motor. It is best to turn off the water supply taps and disconnect the power until a technician can inspect the unit.

If you are experiencing these issues across Tamil Nadu, our experienced technicians are ready to help. We offer reliable, same-day service to get your appliance back in working order. Contact us at 99520 78200 to schedule your repair.

Book Your Service Now

Get a Technician Today

Opens WhatsApp with your details pre-filled — we'll confirm your visit window directly. Trouble opening WhatsApp? Call us instead.

📞 Call Now — 99520 78200