Serving Tamil Nadu & Surrounding Areas Mon–Sun: 8AM–9PM Same-Day Response
CALL NOW 99520 78200
Washing Machine Troubleshooting Guide

LG Washing Machine Medic Rinse and Pre Wash Blinking Error

If your LG washing machine display is flashing the 'Medic Rinse' and 'Pre Wash' indicators simultaneously, it typically signals a communication breakdown between the main PCB and the display board. This error can also be triggered by a faulty water level sensor or a voltage fluctuation affecting the control module.

Step-by-Step Reset Procedure

  1. Power off the washing machine by pressing the Power button.
  2. Unplug the power cord from the wall socket completely.
  3. Wait for at least 10 to 15 minutes to allow the capacitors on the PCB to discharge fully.
  4. Plug the machine back in and attempt to start a new cycle to see if the error persists.

Safe Steps to Try Before Calling a Technician

  1. Check your home's main power supply for loose connections or voltage instability.
  2. Inspect the wiring harness between the top control panel and the main board for any signs of rodent damage or loose connectors.
  3. Ensure the water inlet valves are fully open and there is adequate water pressure, as low pressure can sometimes confuse the sensor logic.
  4. Clean the drain pump filter to ensure no debris is causing a system-wide sensor error.

Always disconnect the power supply before opening any panels. If you are uncomfortable handling electrical components, please contact a certified technician to avoid the risk of electric shock.

How It Works

  1. 1

    Call or WhatsApp

    Tell us the appliance, issue, and your area.

  2. 2

    Technician Visits

    We inspect the unit and give an upfront quote.

  3. 3

    Repair & Pay

    Approve the quote, repair completed same-day, pay after.

Why Choose Us

What You Get With Every Repair

30-Day Repair Warranty

If the same issue recurs within 30 days of the repair, we'll fix it again at no extra visit charge.

Frequently Asked Questions

Does this blinking pattern always mean the PCB is damaged?

Not necessarily. While it often points to a communication error, it can also be caused by a loose wire or a temporary glitch due to power surges common in many areas.

Can I continue using the machine if the lights are blinking?

No, the machine will likely remain in a locked state for safety reasons. It is best to perform the reset procedure before attempting further use.

What should I do if the reset procedure does not stop the blinking?

If the lights continue to blink after a hard reset, the issue is likely a hardware failure in the PCB or a faulty sensor that requires professional diagnostic equipment.

Is this error related to the water supply?

Sometimes, if the machine cannot detect water levels correctly, it may trigger a sensor fault. Ensure your inlet hoses are not kinked or blocked.

Troubleshooting LG Washing Machine Medic Rinse and Pre Wash Blinking

If you notice the "Medic Rinse" and "Pre Wash" indicators blinking simultaneously on your LG washing machine, it is often a signal that the appliance has encountered a control system error. In most cases, this specific blinking pattern points to a communication breakdown between the main Printed Circuit Board (PCB) and the display interface, or it may indicate a fault with one of the machine's internal sensors, such as the water level or door lock sensor.

How to Perform a Hard Reset

Before assuming a hardware failure, you can attempt a manual reset to clear temporary electronic glitches:

  1. Power off your washing machine completely.
  2. Unplug the power cord from the wall socket.
  3. Wait for at least 10 to 15 minutes to allow the capacitors on the PCB to discharge fully.
  4. Plug the machine back in and attempt to start a new cycle.

If the lights continue to blink after the reset, the issue likely requires professional technical intervention to inspect the wiring harness or replace a faulty control board.

Does this blinking pattern always mean the PCB is broken?

Not necessarily. While it often relates to the PCB, it can also be triggered by loose wiring connections or a malfunctioning sensor. A thorough diagnostic check is required to isolate the exact component causing the communication error.

Can I fix this error myself?

You can perform the reset procedure mentioned above. However, if the error persists, we recommend avoiding DIY repairs on the internal electronics to prevent further damage. Our independent technicians are experienced in handling complex LG washing machine repairs across Tamil Nadu.

If you are unable to resolve the blinking lights, our team is ready to assist you with reliable, same-day service. Contact us at 99520 78200 to schedule a visit.

Book Your Service Now

Get a Technician Today

Opens WhatsApp with your details pre-filled — we'll confirm your visit window directly. Trouble opening WhatsApp? Call us instead.

📞 Call Now — 99520 78200